Tuned cylinder pics.

Questions and answers about the Yamaha FS1
Plaats reactie
Flika
100km gereden
100km gereden
Berichten: 190
Lid geworden op: 29 jun 2008, 11:19

Tuned cylinder pics.

Bericht door Flika »

Here's some pics of a 43mm cast iron cylinder I did a while ago

Afbeelding

Afbeelding

Afbeelding

Afbeelding

Afbeelding
Dion k80

Bericht door Dion k80 »

You did the exhaust in a not so normal but genius way ;)

I did some cylinders with this construction... only the exhaust... there you have to built a specially made one... because the flow in the pipe is different ;)

a homoet or something wont run nice on this cylinder :D
mpro09
10000km gereden
10000km gereden
Berichten: 14285
Lid geworden op: 10 nov 2006, 15:31
Locatie: Hilversum
Contacteer:

Bericht door mpro09 »

that will rev quite high I guess :lol:
Flika
100km gereden
100km gereden
Berichten: 190
Lid geworden op: 29 jun 2008, 11:19

Bericht door Flika »

Strangely enough this cylinder will be quite low revs as it is, probably 11k with the right pipe. Durations are quite low with a low blowdown figure so will make good torque. I ran this shape exhaust port on the Notso Special and it was nice to ride with a really good power spread but really came alive when it hit the powerband.There is scope to increase the exhaust duration by another 10 or more degrees but the rider is heavy and we want it to pull well, so will try it and see and maybe lift the port more later.


We may try it with a Homoet pipe and see, should be ok with such a low exhaust port.
Gebruikersavatar
degoelaman
100km gereden
100km gereden
Berichten: 204
Lid geworden op: 19 apr 2009, 09:31
Locatie: Hoorn

Bericht door degoelaman »

Great porting :bow:
May I ask what your durations are?
Flika
100km gereden
100km gereden
Berichten: 190
Lid geworden op: 29 jun 2008, 11:19

Bericht door Flika »

No problem, very low exhaust duration on this to leave room for more development. Ex 180 Trans 130 boost 128 with single base gasket fitted.
Gebruikersavatar
degoelaman
100km gereden
100km gereden
Berichten: 204
Lid geworden op: 19 apr 2009, 09:31
Locatie: Hoorn

Bericht door degoelaman »

Flika schreef:No problem, very low exhaust duration on this to leave room for more development. Ex 180 Trans 130 boost 128 with single base gasket fitted.


Oke thanks, the exhaust duration is low indeed, but, like you said, you can make it higher for development.
but how width is the exaust port? You can make it very width in the shape you have make it, can't you?
Flika
100km gereden
100km gereden
Berichten: 190
Lid geworden op: 29 jun 2008, 11:19

Bericht door Flika »

From memory I think the widest part of exhaust port was 40mm, haven't got the cylinder to measure as it was for someone else.
Gebruikersavatar
degoelaman
100km gereden
100km gereden
Berichten: 204
Lid geworden op: 19 apr 2009, 09:31
Locatie: Hoorn

Bericht door degoelaman »

Flika schreef:From memory I think the widest part of exhaust port was 40mm, haven't got the cylinder to measure as it was for someone else.

Oke, that is a very wide port.
Thanks for your information!
Plaats reactie